Operating Instructions and Parts Manual Models JJP-12 and JJP-12HH Jointer-Planer WALTER MEIER (Manufacturing) Inc. 427 New Sanford
10 Power Once a properly rated plug is connected, plug power cord into outlet. Press the green on button (A, Fig. 4) to start. Press the red off butt
11 handle for a deeper cut. 3. Tighten the lock knob (D). The infeed table lifting handle in the fully lowered position results in a depth of cut of
12 Adjustments Table and Knife Adjustments For accurate jointing, at least three things must be true: 1. Infeed and outfeed tables must be coplanar.
13 Performing the Coplanar Alignment If alignment is required as determined in the previous section, proceed as follows: Disconnect machine from powe
14 Setting Cutterhead Knives (Straight Knives Only) Important: Before performing any adjustments in this section, the infeed and outfeed tables must
15 Replacing Cutter Knives (Straight Knives Only) Disconnect machine from power source before making any adjustments. Failure to comply may cause se
16 these elements can prevent the insert from seating properly, and may affect the quality of the cut. Before installing each screw, lightly coat the
17 Cutterhead Drive Belt Replacement 4. Loosen four motor mount screws (L). Lift the motor and rest it in the horizontal slot side of the motor mount
18 Planer Table Adjustment Disconnect machine from power source before making any adjustments. Failure to comply may cause serious injury. Checking
19 Basic Operations Dust Collection Before initial operation, the machine must be connected to a dust collector. Initial Startup After the assembly a
2 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Au
20 Direction of Grain Avoid feeding work into the jointer against the grain (Figure 18). Figure 18 This may result in chipped and splintered edges.
21 For wood less than 3 inches wide – use beveled push blocks and apply pressure toward the fence. Keep fingers near top of push block. Several passe
22 Feeding the Work The planer is supplied with planer blades mounted in the cutterhead and infeed and outfeed rollers adjusted to the correct height
23 Maintenance Blade Care Blades are extremely sharp! Use caution when cleaning or changing. Failure to comply may cause serious injury! The condit
24 Troubleshooting Performance Troubleshooting – Jointer Trouble Probable Cause Remedy Finished stock is concave on back end. Knife is higher than o
25 Performance Troubleshooting – Planer Trouble Probable Cause Remedy Snipe Note: Snipe cannot be eliminated, but can be so minimized as to become
26 Mechanical Troubleshooting – Planer/Jointer Trouble Probable Cause Remedy Chain jumping. Inadequate tension. Adjust chain tension. Sprockets misa
27 Parts List Index No. Part No. Description Size Qty 1 ... TS-1541031 ...Lock Nut ...
28 Index No. Part No. Description Size Qty 78 ... TS-1491031 ...Hex Cap Screw ...
29 Index No. Part No. Description Size Qty 162 ... JJP12-162 ...Front Cover ...
3 Table of Contents Warranty and Service ...
30 Index No. Part No. Description Size Qty 289 ... TS-2246122 ...Button Head Socket Screw ...M6x1
31 Index No. Part No. Description Size Qty 381 ... JJP12-381 ...Cutterhead Cover ...
32 Assembly Drawings Infeed Table Assembly
33 Outfeed Table Assembly
34 Cutterblock Assembly
35 Base Assembly
36 Motor Assembly
37 Planer Table Assembly
38 Fence Assembly
39 Electrical Connection Accessories Stock No Description 708821 ...Replacement Knives for JJP-12 Jointer-planer (set of 3) 1791212
4 Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings post
40 Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for business
5 21. Make your workshop child proof with padlocks, master switches or by removing starter keys. 22. Give your work undivided attention. Looking aro
6 39. At all times hold the stock firmly. 40. Do not use this machine for other than it intended use. If used for other purposes, Walter Meier (Man
7 Specifications Model number ... JJP-12...
8 Features and Terminology Figure 1 – Features and Terminology Receiving Carefully unpack the machine and any loose items from the wood crate and i
9 Operating Controls Disconnect machine from power source before making any adjustments. Failure to comply may cause serious injury. Cutterhead kn
Kommentare zu diesen Handbüchern