Operating Instructions and Parts Manual Disc, Belt and Combination Disc/Belt Sanders Models: J-4200A J-4300A J-4400A J-4200A-2 J-4301A J-4401A
107.0 Maintenance 7.1 Belt replacement 1. Disconnect the power to the machine to prevent accidental start-ups. If the machine is plugged into an o
11built up material in the upper part of the bracket casting. 2. Take the two keys off of the idler pin bracket, wipe off, and re-grease. 3. Revers
12 Figure 11: Rotating the machine casting to remove the disc guard bolts Figure 12: Locating the set screws that secure the disc to the arbor 8. T
13 Figure 14: Loosening pulley set screws to allow the adjustment of pulley on arbor shaft. 8.0 Machine setup 8.1 Basic setup 1. Position the mach
144. Move the measuring device to the opposite edge of the disc and measure the distance to the miter slot. 5. Adjust the table by loosening the fo
15 Figure 20: Location of adjustment (socket head) screws and pointer attachment screw for table angle adjustment. Figure 21: Locations of stop lug
16 All electrical service work on your JET sander should be performed by a qualified, licensed electrician who is familiar with all safe standard el
1710.0 Troubleshooting Symptom Possible Cause Correction Motor will not run Voltage is too low. Check power supply for proper voltage. Branch cir
1811.0 Replacement parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Mo
1911.1.2 Model J-4200A Belt and Disc Sander Assembly – Parts List IndexNo PartNo Description Size Qty1 ... J-5508427 ...
21.0 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of ou
20IndexNo PartNo Description Size Qty63 ... J-5508457 ... Platen...
2111.2.1 Model J-4300A Belt Sander Assembly – Exploded View
2211.2.2 Model J-4300A Belt Sander Assembly – Parts List IndexNo PartNo Description Size Qty1 ... J-5508427 ... Br
23IndexNo PartNo Description Size Qty63 ... J-5508457 ... Platen...
2411.3.1 Model J-4400A Disc Sander Assembly – Exploded View
2511.3.2 Model J-4400A Disc Sander Assembly – Parts List IndexNo PartNo Description Size Qty1 ... J-5508438 ... Be
2611.4.1 Base Assembly: Model J-4300A, 1 Phase – Exploded View
2711.4.2 Base Assembly: Model J-4300A, 1 Phase – Parts List IndexNo PartNo Description Size Qty1 ... J-5511743 ...
2811.5.1 Base Assembly: Model J-4300A, 3 Phase – Exploded View
2911.5.2 Base Assembly: Model J-4300A, 3 Phase – Parts List IndexNo PartNo Description Size Qty1 ... 4202A-501...
32.0 Table of contents Section Page 1.0 Warranty and Service ...
3011.6.1 Base Assembly: Model J-4200A & 4400A, 1 Phase – Exploded View
3111.6.2 Base Assembly: Model J-4200A & 4400A, 1 Phase – Parts List IndexNo PartNo Description Size Qty1 ... AB605418 ...
3211.7.1 Base Assembly: Model J-4200A & 4400A, 3 Phase – Exploded View
3311.7.2 Base Assembly: Model J-4200A & 4400A, 3 Phase – Parts List IndexNo PartNo Description Size Qty1 ... AB605419 ...
3412.1 Electrical schematic – single phase
3512.2 Electrical schematic – 3 phase
36 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettoo
4 3.0 Safety Warnings General Cautions - Misuse of this machine can cause serious injury. - For safety, the machine must be set up, used and ser
518. Keep hands in sight and clear of all moving parts and cutting surfaces. 19. All visitors should be kept at a safe distance from the work area.
64.0 Machine and Manual Overview JET Abrasive Finishing Machines are available in three different configurations: disc, belt, and combination disc a
75.0 Specifications Model Stock No. J-4200A 414551 J-4200A-2 414552 J-4202A 414553 J-4300A 414600 J-4301A 414601 J-4400A 414602 J-4
86.0 Operating instructions These sanders can be used to remove stock from a wide variety of machinable materials. Different materials require diffe
9To adjust to horizontal: 1. Unlock both lock bolts. 2. Move arm to horizontal until it contacts its stop. (See Figure 3.) 3. Tighten both lock bo
Kommentare zu diesen Handbüchern